Personal Service
Shipping within 24h
30 days money back guarantee
Aftersales Service
Hotline +49 521 91 510 412

Steca Power Tarom 4140

€1,479.90*

Available in 1 day, delivery time 2-5 days

Product number: 030401026
Product information "Steca Power Tarom 4140"

Steca Power Tarom 4140

  • High End State of Charge control (SOC)
  • Professional battery care
  • Full grafical display
  • Automatic battery voltage detection
  • Full load protection
Specially designed for industrial and outdoor applications, the Steca Power Tarom comes with an IP 65 casing made of powder-coated steel.
Product features
  • Hybrid controller
  • State of charge determination with Steca AtonIC (SOC)
  • Automatic detection of voltage
  • PWM control
  • Multistage charging technology
  • Load disconnection depending on SOC
  • Automatic load reconnection
  • Temperature compensation
  • Common positive or negative grounding on one terminal
  • Integrated data logger
  • Night light function with Steca PA 15
  • Integrated self test
  • Monthly maintenance charge
  • Integrated energy meter
Electronic protection functions
  • Overcharge protection
  • Deep discharge protection
  • Reverse polarity protection of module, load and battery
  • Reverse polarity protection by internal fuse
  • Automatic electronic fuse
  • Short circuit protection of load and module
  • Overvoltage protection at module input
  • Open circuit protection without battery
  • Reverse current protection at night
  • Overtemperature and overload protection
  • Battery overvoltage shutdown
Displays
  • Text LCD display
    - for operating parameters, fault messages, self test
Operation
  • Simple menu-driven operation
  • Programming by buttons
  • Manual load switch
Interfaces
  • RJ45 interface
Options
  • External temperature sensor (included)
  • Alarm contact
  • System monitoring via a Steca PA CAB1 Tarcom
Certificates
  • Approved by the World Bank for Nepal
  • Fit for use in tropical areas (DIN IEC 68 part 2-30)
  • Compliant with European Standards (CE)
  • Made in Germany
  • Developed in Germany
  • Manufactured according to ISO 9001 and ISO 14001

This solar charge controller can be used to control system sizes of up to 8,400 Wp at three voltage levels (12 V, 24 V, 48 V). The Steca Power Tarom is based on the technology of the Steca Tarom controller. When connected in parallel, several controllers from this series can be operated via a standard DC bus in a simple solar home system or a hybrid system. This allows an output of over 20 kWp to be reached.

 

Properties "Steca Power Tarom 4140"
Ausgleichsladung (V): 58,8
Boostladespannung (V): 57,6
Eigenverbrauch (mA): 14
Gewicht (kg): 10,0
Ladeendspannung (V): 54,8
Laststrom (A): 70
Leerlaufspannung Solarmodul (V): < 100
Länge / Breite (Tiefe) / Höhe (mm): 360 / 330 / 190
Modulstrom (A): 140
Schutzart (IP): 65
Systemspannung (V): 48
Umgebungstemperatur (°C): -10 - +60

0 of 0 reviews

Leave a review!

Share your experiences with other customers.


Accessory Items

Steca PA Tarcom 01
Steca PA Tarcom 01 The Steca PA Tarcom data logger is connected to the RJ45 interface of the Steca Power Tarom charge controller, or via the Steca PA HS200.The data logger is available in several different versions: as a simple RS232 interface to directly save and read data on the PC or Laptop (Steca PA Tarcom 01), as a data logger with an integrated analogue modem (Steca PA Tarcom RMT), as a data logger with an integrated GSM modem for remote monitoring (Steca PA Tarcom GSM) and as a data logger with an Ethernet interface for connection to a PC network (Steca PA Tarcom Ethernet). The Steca PA Tarcom is delivered with its accompanying software. Product features 4 years maximum storage capacity (1 Mbit) Adjustable logging intervals Stores 8 data sets at programmed intervals Freely programmable alarm states Displays LED shows operating states Interfaces RJ45 communication interface to Steca Power Tarom RS232 serial interface to PC Analogue sensor input e.g. for radiation or wind speed Alarm contact Tarcom software Data transfer by modem or by text message Downloads data from the logger to a PC List of data sets can be exported to MS-EXCEL Graphic visualisation of data sets (values/time) Analyzes energy flows (Ah) within a PV hybrid system Activation and selection of alarm types Setting the interval for calls and for sending text messages Configures the telephone number and text message recipient Tells the data logger at what time it has to call Alarms can be set by text message Certificates Compliant with European Standards (CE) Made in Germany Developed in Germany  

€489.90*
Steca PA Tarcom GSM
Steca PA Tarcom GSM The Steca PA Tarcom data logger is connected to the RJ45 interface of the Steca Power Tarom charge controller, or via the Steca PA HS200.The data logger is available in several different versions: as a simple RS232 interface to directly save and read data on the PC or Laptop (Steca PA Tarcom 01), as a data logger with an integrated analogue modem (Steca PA Tarcom RMT), as a data logger with an integrated GSM modem for remote monitoring (Steca PA Tarcom GSM) and as a data logger with an Ethernet interface for connection to a PC network (Steca PA Tarcom Ethernet). The Steca PA Tarcom is delivered with its accompanying software. Product features 4 years maximum storage capacity (1 Mbit) Adjustable logging intervals Stores 8 data sets at programmed intervals Freely programmable alarm states Displays LED shows operating states Interfaces RJ45 communication interface to Steca Power Tarom RS232 serial interface to PC Analogue sensor input e.g. for radiation or wind speed Alarm contact Tarcom software Data transfer by modem or by text message Downloads data from the logger to a PC List of data sets can be exported to MS-EXCEL Graphic visualisation of data sets (values/time) Analyzes energy flows (Ah) within a PV hybrid system Activation and selection of alarm types Setting the interval for calls and for sending text messages Configures the telephone number and text message recipient Tells the data logger at what time it has to call Alarms can be set by text message Certificates Compliant with European Standards (CE) Made in Germany Developed in Germany  

€959.90*
Steca PA 15
Steca PA 15 The Steca Tarom and Power Tarom charge controllers send out signals (125 kHz on 300 Baud) which are modulated on the DC cable and received by the Steca PA 15 remote control.These signals contain information on the batteries' state of charge (SOC). The Steca PA 15 features five different operating modes (see below) which can be set using five different jumper positions. The maximum switching capacity of 15 A can be increased with a Steca PA EV200 DC relay to up to 200 A if desired. Product features Receives information on SOC and time (day/night) Load control via priority assignment Adjustable SOC thresholds Connects a maximum of 9 solar arrays in parallel Current surge switch function Electronic protection functions Switches off load if there is no signal Reverse polarity protection by internal fuse Overtemperature and overload protection Operation Configuration by jumpers Modes of operation Management of parallel solar generators When the battery is full, excess energy is redirected to additional loads such as pumps, water heaters Automatic start / stop of diesel or wind back-up generators Night light function Acoustic alarm at deep discharge or overheating  

€129.90*
Steca PA CAB1
Steca PA CAB1 Tarcom Steca data cables are used to connect the Steca Tarom and Steca Power Tarom solar charge controllers to a PC via a USB port. This allows direct monitoring of a system without using a data logger. This feature is especially suitable for short-term system monitoring and on-site testing. The most important system information is transferred to the PC in real time and can be conveniently analysed and graphically visualised using the Steca TarCom software.To use this convenient data transfer system a driver and the Steca TarCom software must first be installed on the PC (Download available at www.stecasolar.com).„Tarom RJ45 in“ can be selected under options/settings/extra in the Steca TarCom software menu system. The software then directly accesses the data from the Steca Power Tarom solar charge controller and displays this on the PC.

€54.90*
Steca PA Tarcom RM / RMT
Steca PA Tarcom RM / RMT The Steca PA Tarcom data logger is connected to the RJ45 interface of the Steca Power Tarom charge controller, or via the Steca PA HS200.The data logger is available in several different versions: as a simple RS232 interface to directly save and read data on the PC or Laptop (Steca PA Tarcom 01), as a data logger with an integrated analogue modem (Steca PA Tarcom RMT), as a data logger with an integrated GSM modem for remote monitoring (Steca PA Tarcom GSM) and as a data logger with an Ethernet interface for connection to a PC network (Steca PA Tarcom Ethernet). The Steca PA Tarcom is delivered with its accompanying software. Product features 4 years maximum storage capacity (1 Mbit) Adjustable logging intervals Stores 8 data sets at programmed intervals Freely programmable alarm states Displays LED shows operating states Interfaces RJ45 communication interface to Steca Power Tarom RS232 serial interface to PC Analogue sensor input e.g. for radiation or wind speed Alarm contact Tarcom software Data transfer by modem or by text message Downloads data from the logger to a PC List of data sets can be exported to MS-EXCEL Graphic visualisation of data sets (values/time) Analyzes energy flows (Ah) within a PV hybrid system Activation and selection of alarm types Setting the interval for calls and for sending text messages Configures the telephone number and text message recipient Tells the data logger at what time it has to call Alarms can be set by text message Certificates Compliant with European Standards (CE) Made in Germany Developed in Germany  

€879.90*
Steca PA Tarcom Ethernet
Steca PA Tarcom Ethernet The Steca PA Tarcom data logger is connected to the RJ45 interface of the Steca Power Tarom charge controller, or via the Steca PA HS200.The data logger is available in several different versions: as a simple RS232 interface to directly save and read data on the PC or Laptop (Steca PA Tarcom 01), as a data logger with an integrated analogue modem (Steca PA Tarcom RMT), as a data logger with an integrated GSM modem for remote monitoring (Steca PA Tarcom GSM) and as a data logger with an Ethernet interface for connection to a PC network (Steca PA Tarcom Ethernet). The Steca PA Tarcom is delivered with its accompanying software. Product features 4 years maximum storage capacity (1 Mbit) Adjustable logging intervals Stores 8 data sets at programmed intervals Freely programmable alarm states Displays LED shows operating states Interfaces RJ45 communication interface to Steca Power Tarom RS232 serial interface to PC Analogue sensor input e.g. for radiation or wind speed Alarm contact Tarcom software Data transfer by modem or by text message Downloads data from the logger to a PC List of data sets can be exported to MS-EXCEL Graphic visualisation of data sets (values/time) Analyzes energy flows (Ah) within a PV hybrid system Activation and selection of alarm types Setting the interval for calls and for sending text messages Configures the telephone number and text message recipient Tells the data logger at what time it has to call Alarms can be set by text message Certificates Compliant with European Standards (CE) Made in Germany Developed in Germany  

€799.90*
Steca PA HS 200
Steca PA HS 200 The Steca PA HS200/400 is a highly intelligent current sensor with extremely low own consumption.The Steca PA HS200/400 is a highly intelligent current sensor with extremely low own consumption.The Steca PA HS200/400 comes into play when (e.g.) an inverter is directly connected to the battery and the charge controller cannot measure the current consumption. A shunt is also required when an additional generator (e.g. PV, wind or diesel) directly charges the battery. The current is measured contact-free via a Hall-effect sensor. The data is transmitted to the charge controller over a cable connection. All types of current flows can be detected: charge current, load current and battery and DC-side inverter current flows.The Steca PA HS200 has been developed for applications with the Steca Power Tarom. The PA HS400 can be used exclusively with the Steca Tarom MPPT 6000-M.

€329.00*